CALREC ARTEMIS MANUAL PDF

Any DIP switches labelled Address 2 should all be set to the off position. Delay mono legs of delay, for Artemis Shine however the amount of delay per leg remains unchanged at 2. The SW-P connection is made to manial router card in the processing rack artrmis as the Master Router the same processing rack as the H2O connection, but to the router card rather than the Control Processor. User Control Logging Setup Basically the system captures control data and attaches a timestamp to establish when various controls changes were applied by the operator on Apollo, Artemis and Summa Consoles and puts the results into a logging file. Note that the OB stands are slightly taller than their studio equivalents, sitting the control surface 7. Ports are selected by clicking on them.

Author:Akijora Akinohn
Country:Paraguay
Language:English (Spanish)
Genre:Career
Published (Last):10 October 2009
Pages:70
PDF File Size:2.89 Mb
ePub File Size:15.42 Mb
ISBN:939-8-65637-212-9
Downloads:9109
Price:Free* [*Free Regsitration Required]
Uploader:Vikinos



Any DIP switches labelled Address 2 should all be set to the off position. Delay mono legs of delay, for Artemis Shine however the amount of delay per leg remains unchanged at 2. The SW-P connection is made to manial router card in the processing rack artrmis as the Master Router the same processing rack as the H2O connection, but to the router card rather than the Control Processor.

User Control Logging Setup Basically the system captures control data and attaches a timestamp to establish when various controls changes were applied by the operator on Apollo, Artemis and Summa Consoles and puts the results into a logging file.

Note that the OB stands are slightly taller than their studio equivalents, sitting the control surface 7. Ports are selected by clicking on them. Page of Go. Patching Input Sources To Faders!! The installation should be carried out in accordance with all applicable installation rules and regulations. The lower section of the panel works in conjunction The level control and source also appear on the Artemis Monitor Panel.

Calrec Hydra2 User guide The units may also be housed in any air conditioned bay. Got it, majual to print. Cleaning For cleaning the front panels of the equipment we recommend using a soft anti-static cloth, lightly dampened with water if required. PFL outputs there are also Mon2 but also individual level trim functions. Only ports inside the aliases that are at the same sample rate as the desk will work.

This allows for cards to be moved around within the same rack to aid troubleshooting if hardware problems are experienced as well as ensuring the backup is correct ,anual the event of a hotswap. In a multi-rack system, one of the racks needs to be dedicated as the Master Router and the router cards in this rack should be configured as such. To exit the routing screen for the selected bus type and return back to the routing overview, touch the CLOSE button.

Select port 1 and click Edit to view the details for the serial port. Full — sends the full surround signal out to containing APFL controls is explained the speakers. User Splits Please refer Clicking the Reset all to User 1 button will to the monitoring section for details on remove all user splits.

Please refer Clicking the Reset all to User 1 button will to the monitoring section for details on remove maunal user splits. See Fig 11 below right. Port Grouping Maunal lists are sorted alphabetically which will not always place related ports together. This provides access to useful broadcast with fader and monitor panels. Got it, continue to print. Technical Support Once your console is installed we can Repairs provide an engineer on site to carry out If you need to return goods to Calrec, for system commissioning.

No Link for independent operation. Slot labels are printed across the upper fixing rail and each card has a small circular hole in the upper left corner through which the slot label can be seen.

These connections are NOT supplied and secondary. The Grass Valley Jupiter system counts from 0 but also uses its physical level numbers rather than SW-P values in its config. When you have finished editing, the file should be saved as a. Manufacturers refer to these two instances differently and so documentation for specific 3rd party devices should be consulted. Most Related.

ELISABETH KUBLER ROSS SOBRE EL DUELO Y EL DOLOR PDF

Calrec Artemis Manuals

If a port appears in more than one folder, removing access to it from one will also change the display of the other folder to reflect the change of access. The order the ports are displayed in can be changed by clicking on the column headers at the top of the table. Table of Contents Add to my manuals Add. Two of these protocols can directly affect control surface operation. The Boxes — function can be used to remove boxes that are no longer required, or that have been added in error. Please note that only ID values between 0 and are currently supported. Clicking PATCH makes the cross point patch and routes audio from the selected input to the selected calfec.

UNA CANCION PARA TI SARAH DESSEN PDF

Calrec ARTEMIS Operator's Manual

The newly created Hydra Patchbays also become available to consoles. Page The following summarises key new features by the software version in which they were introduced. For a complete list of worldwide distributors by region, go to www. Distances are only limited by the SFP type. External ccalrec, supporting the SW-P protocol, can also have access to Hydra patchbays enabling 3rd party control over console patching. For customers outside the UK and Ireland, shipping via the distributor saves customers from dealing with exportation paperwork. Consoles can patch signals to their own or shared Hydra Patchbay inputs in the same way they patch to physical output ports.

2SK956 PDF

CALREC ARTEMIS MANUAL PDF

.

BUDDY SCALERA PDF

.

Related Articles